The 10 Best Einhell Chainsaws Offers in UK - May 2024

Starting a chainsaw from Einhell is quite simple and straightforward, but it requires proper knowledge and skills to prevent accidents. Here are some steps to follow when starting an Einhell chainsaw:

1. Check the saw: Before starting the saw, you should give it a quick inspection. Check the chain to make sure it is tight and the bar is in good condition. Ensure that the air filter is clean and the gas and oil tanks have enough fluids.

2. Fuel mix: Next, ensure that the fuel mix is correct. Einhell chainsaws use a 2-stroke engine that requires the use of a proper fuel mix. Usually, the fuel should consist of gasoline and oil mixed in a specific ratio. You can check the Einhell chainsaw manual to know the recommended ratio.

3. Starting the engine: Once everything is set up, it's time to start the engine. Turn the on/off switch to the "on" position. Then, set the choke lever to the closed position. Place the saw on a flat surface, hold the front handle with your left hand and the rear handle with your right hand. Put your foot on the rear handle and pull the starter cord firmly. Repeat until the engine starts.

4. Adjusting the choke: Once the engine starts, you should adjust the choke lever to the open position. You can then use the throttle trigger to adjust the engine to the idle speed. You can now remove your foot from the rear handle.

5. Warm-up period: After starting the engine, allow it to idle for a while for the engine to warm up. Usually, a warm-up period of 30 seconds to a minute is enough. During this period, don't apply full throttle as it may damage the engine.

6. Ready to use: Finally, your Einhell chainsaw is ready to use. You can now apply full throttle and start cutting or trimming. Ensure you use the saw following all safety recommendations provided by the manufacturer.

In conclusion, starting an Einhell chainsaw is relatively easy, but it requires proper handling to prevent accidents. Always ensure that everything is in good condition and that you follow all manufacturer recommendations. By doing so, you can ensure that your chainsaw remains safe, efficient, and long-lasting.

If you own an Einhell chainsaw, it is important to know how to adjust the chain. A loose chain can reduce the effectiveness of your tool, and a tight one can cause damage or injury. The process of adjusting the chain is quite simple and can be done in a few easy steps.

First, ensure that the chainsaw is turned off and the chain brake is engaged. This ensures your safety while working on the chainsaw. Next, locate the adjustment screws. They are usually located on the side or bottom of the chainsaw, near the chain. Some models may have a single screw, while others have two.

If your chainsaw has a single screw, it is used to adjust the tension of the chain. Turning the screw clockwise will tighten the chain, while turning it counterclockwise will loosen it. If you have two screws, one is used to adjust the tension, and the other is used to adjust the height of the chain.

To adjust the tension, loosen the nuts on the bar and move the bar towards the engine. Then, use the adjustment screw to tighten the chain to the correct tension. The chain should be tight enough to stay on the bar, but still loose enough to be easily pulled off the bar by hand.

Once you have adjusted the chain tension, it is important to check the alignment of the chain. Use a straight edge to check the alignment of the bar and the chain. If they are not straight, adjust the height of the chain using the second screw until they are aligned.

After you have adjusted the chain tension and alignment, check the oiler. The oiler should be adjusted to ensure that the chain is properly lubricated. If the oiler is not working correctly, the chain will become dry, which can cause damage to the chain and bar.

In conclusion, adjusting the chain on an Einhell chainsaw is essential to maintain the efficiency and safety of your tool. The steps involved are simple and easy to follow. Ensure that you follow the instructions carefully, and always double-check that the chainsaw is turned off and the chain brake is engaged before making any adjustments.

When it comes to choosing the optimal bar length for an Einhell chainsaw, there are a few factors to consider. The bar length refers to the length of the cutting blade on the chainsaw and is measured from the tip of the blade to the point where it enters the chainsaw.

One important factor to consider is the type of work you will be using the chainsaw for. If you are using the chainsaw for small, light-duty tasks such as trimming tree branches or cutting firewood, a shorter bar length of around 12 to 16 inches may be suitable. This length is also easier to maneuver in tight spaces and requires less effort to control.

However, if you are using the chainsaw for larger jobs such as felling trees or cutting logs, a longer bar length of 18 to 20 inches may be more appropriate. This length allows the chainsaw to cut through thicker logs and trees more efficiently, reducing the amount of time and effort required.

Another factor to consider is the power and weight of your Einhell chainsaw. A longer bar length requires more power to operate and can be more challenging to handle. If your Einhell chainsaw is relatively small and lightweight, it may not have enough power to operate a longer bar length effectively.

It is also essential to consider your level of experience with chainsaws. If you are a beginner or inexperienced in chainsaw use, it is recommended to start with a shorter bar length to avoid any accidents or injuries. Additionally, it is crucial to invest in protective gear such as chainsaw chaps, gloves, and a helmet to ensure your safety while operating the chainsaw.

In conclusion, the optimal bar length for an Einhell chainsaw depends on the type of task you will be using it for, the power and weight of the chainsaw, and your level of experience. It is essential to consider all these factors before making your choice and to invest in protective gear to ensure safe operation.

Maintaining an Einhell chainsaw is essential for prolonging the life of your tool and maximizing its performance. Here are some tips on how to maintain your Einhell chainsaw:

1. Regular cleaning: After every use, it is important to remove any debris, dirt, or wood chips that have accumulated on the chainsaw. You can use a soft-bristled brush to remove the debris and a damp cloth to wipe down the chainsaw. Cleaning ensures that no residue gets into the internal parts of the chainsaw and clogs the air filters or carburetor.

2. Sharpening the chain: If the chain on your Einhell chainsaw is dull, you must sharpen it to prevent damage to your chainsaw. The best way to sharpen your chainsaw is to use a chainsaw file guide. The file guide ensures that you sharpen the teeth at a consistent angle. It is essential to wear protective gloves and eyewear when sharpening the chain.

3. Checking and replacing the air filter: Regularly check your Einhell chainsaw's air filter for dirt, dust, and debris that can clog the filter and reduce air flow. If the filter is dirty, clean it with soap and water, and replace it if necessary. A clogged air filter can cause engine damage and compromise the chainsaw's overall performance.

4. Checking and replacing the spark plug: The spark plug on your Einhell chainsaw is essential for starting the engine. Over time, the spark plug can become fouled or worn out, causing starting problems or poor engine performance. Check your spark plug regularly, and replace it if necessary. It is essential to use the recommended spark plug for your chainsaw.

5. Lubricating the chainsaw: Proper lubrication is important to prevent premature wear and tear on your chainsaw's engine and chain. Use only high-quality chainsaw oil and lubricate the chain regularly to ensure smooth operation. It is also essential to keep the oil reservoir full.

6. Storing the chainsaw correctly: After every use, store your Einhell chainsaw in a dry, cool, and well-ventilated place. Remove the chain and bar, clean them, and store them separately. This prevents rusting and prolongs their life. Always use the chainsaw cover to protect it from dust and debris.

Maintaining an Einhell chainsaw is vital for ensuring optimal performance and long life. By following these simple tips, you can keep your chainsaw in good condition and avoid costly repairs.

When using an Einhell chainsaw, it is important to use the right type of chain oil to ensure optimal performance of the saw as well as to protect the chain from rapid wear and tear.

The Einhell chainsaw is a petrol-powered saw and as such, it requires chain oil that is specifically formulated for lubricating chainsaw chains. The oil should be designed to perform under high-temperature conditions and to withstand the high loads that the chain is exposed to during use.

One option for Einhell chainsaws is a mineral-based chain oil that is suitable for most cutting applications. This type of oil is designed to provide protection against chain wear while also preventing rust and corrosion. It is a cost-effective option that delivers good performance and is easily available.

For those who want even better performance and protection for their chainsaw chains, Einhell recommends using a synthetic-based chain oil. This oil has been developed with advanced lubrication technology that provides excellent anti-wear properties as well as superior protection against rust and corrosion.

Regardless of the type of chain oil used, it is crucial to ensure that the oil is compatible with the Einhell chainsaw. Using the wrong type of oil can cause damage to the saw as well as increase the risk of accidents. It is also important to follow the manufacturer's instructions when it comes to the amount of oil to be used and the frequency of oiling the chain.

In summary, when it comes to choosing chain oil for an Einhell chainsaw, there are a few options available to ensure optimal performance and chain protection. Using a mineral-based oil is a cost-effective option, while synthetic-based oils offer superior performance and protection. Always ensure that the oil is compatible with the saw and follow the manufacturer's instructions for use. By doing so, you can keep your Einhell chainsaw in top condition and extend its lifespan.

Einhell chainsaws are known for their durability, reliability, and power. However, just like any other power tool, they can encounter certain issues that require troubleshooting. In this article, we will discuss some of the most common issues with Einhell chainsaws and how to troubleshoot them.

1. Chainsaw will not start: If your Einhell chainsaw is not starting, it could be due to a number of reasons. First, check the fuel level and make sure there is enough fuel in the tank. Also check the spark plug and make sure it is clean and not worn out. If the spark plug is dirty, cleaning or replacing it should solve the issue. If not, check the air filter and carburetor for any clogs or blockages.

2. Chainsaw chain keeps coming off: If the chain on your Einhell chainsaw keeps coming off, it could be due to a loose chain tensioner. Check the owner's manual to learn how to properly adjust the chain tensioner. Also, make sure the chain is properly lubricated and not too loose or tight.

3. Chainsaw is not cutting properly: If your Einhell chainsaw is not cutting properly, it could be due to a dull or damaged chain. Sharpen or replace the chain as necessary. Also, make sure the chain is properly adjusted and lubricated. If the chain is still not cutting properly, it could be due to a damaged guide bar. Inspect the guide bar for any cracks or damage, and replace if necessary.

4. Chainsaw is leaking oil: If your Einhell chainsaw is leaking oil, it could be due to a damaged oil tank or oil pump. Inspect the oil tank and pump for any cracks or damage, and replace if necessary. Also, make sure the oil reservoir is not overfilled, as this can cause leaks.

5. Chainsaw is overheating: If your Einhell chainsaw is overheating, it could be due to a dirty air filter or a clogged carburetor. Clean or replace the air filter and inspect the carburetor for any clogs or blockages. Also, make sure the chain is properly lubricated and not too tight, as this can also cause overheating.

In conclusion, troubleshooting common issues with Einhell chainsaws requires proper maintenance and inspection. Always refer to the owner's manual for specific instructions on how to properly adjust, clean, and maintain your chainsaw. By following these tips, you can keep your Einhell chainsaw running smoothly and efficiently for years to come.

Einhell is a well-known brand in the power tool industry, and the company is famous for its high-quality chainsaws. When you purchase an Einhell chainsaw, you can expect that the product will be durable and designed to last. However, even the best tools can sometimes have issues, which is why Einhell offers a warranty on its products.

The length of the warranty on an Einhell chainsaw varies depending on the model. Typically, the warranty on a chainsaw will last for two or three years. However, some models might have shorter or longer warranty periods, so it is essential to check the product information before making a purchase.

A warranty on an Einhell chainsaw covers any defects in materials or workmanship that might occur during normal use. If you experience any issues with your chainsaw during the warranty period, you can contact Einhell's customer service department to arrange a repair or replacement. If the repair is not possible, then the company will replace the chainsaw for you.

To claim warranty on an Einhell chainsaw, you need to provide proof of purchase. This can be a receipt or an invoice that shows the date of purchase and the product's details. You should also keep the original packaging, as this will help protect the chainsaw during shipping in case of a repair.

It is important to note that the warranty on an Einhell chainsaw does not cover normal wear and tear. This means that if the chainsaw breaks due to user error or misuse, the warranty will not cover the costs of repair or replacement. You should also follow the manufacturer's instructions for care and maintenance to ensure that the chainsaw continues to function correctly.

In conclusion, Einhell stands behind its products and provides a warranty on its chainsaws to give customers peace of mind. The length of the warranty varies depending on the model, but typically lasts for two or three years. If you experience any issues with your chainsaw during the warranty period, you can contact Einhell's customer service department for assistance. Remember to keep your proof of purchase and original packaging in case of a warranty claim.

As a chainsaw owner, you must know the importance of storing your chainsaw properly. It not only prolongs the life of your tool, but also reduces the risk of accidents. In this article, we will discuss the steps you should follow to store your Einhell chainsaw correctly.

Step 1: Drain the Fuel
Before storing your chainsaw for an extended period, it’s essential to drain the fuel. Fuel left unused for long periods can damage the carburetor. You can either let the engine run until the fuel is used up or drain the fuel tank manually. Remember to also remove and clean the air filter and spark plug before storage.

Step 2: Clean and Lubricate the Chain
A clean and lubricated chainsaw chain can save you from the hassle of maintenance in the future. After usage, make sure all debris and sawdust are removed from the chain. Clean the chain and bar using a soft brush and a mild detergent solution. Applying chain oil before storage will keep the chain well lubricated and prevent rust.

Step 3: Store in a Dry Place
Moisture is the biggest enemy of your chainsaw. A damp environment can lead to corrosion, damage to electrical components, and mold growth. Therefore, it’s crucial to store your chainsaw in a dry place where it’s protected from rain and humidity. Placing your chainsaw in a ventilated room or garage is an excellent option.

Step 4: Use a Chainsaw Case
Using a chainsaw case is a great way to keep your tool safe from damage. It protects the chainsaw from dust, moisture, and accidental impacts. Einhell chainsaws come with a protective case, which is essential for proper storage. Make sure to store your chainsaw in the case with the chain guard installed.

Step 5: Maintenance and Inspection
Regular maintenance and inspection are crucial for a chainsaw’s performance and durability. Before using your chainsaw after storage, inspect it thoroughly for any damages or wear and tear. Check for loose screws, damaged parts, and for any signs of rust. Proper maintenance will keep your Einhell chainsaw in top shape and ready for use whenever required.

In conclusion, following these tips will help keep your Einhell chainsaw in top shape and ensure that it’s ready for use whenever required. By draining the fuel, cleaning and lubricating the chain, storing it in a dry place, using a chainsaw case, and performing regular maintenance, your chainsaw can last for years to come. Happy sawing!

The Einhell chainsaw is a powerful and efficient tool that can handle everything from light pruning to heavy-duty woodcutting. One of the important factors to consider when purchasing a chainsaw is its weight. The weight of the chainsaw will impact its ease of use, maneuverability, and overall functionality. In this article, we will discuss the weight of the Einhell chainsaw and its implications for users.

The weight of the Einhell chainsaw varies based on the specific model. Generally, Einhell chainsaws range in weight from around 4.5 kilograms to 6 kilograms. This is a relatively average weight for chainsaws and one that most users can manage. However, if you plan on using the chainsaw for long periods or for tasks that require a lot of movement, you may want to opt for a lighter model.

The weight of the chainsaw is important for several reasons. First, it impacts the user's ability to maneuver the saw. With a heavier chainsaw, users may struggle to move it around trees and other obstacles. This can make the saw less effective and potentially dangerous. On the other hand, a lighter chainsaw will be easier to maneuver and will enable users to work more efficiently.

Second, the weight of the chainsaw affects its overall balance. A poorly balanced chainsaw can cause strain on the user's arms and hands. This can lead to fatigue and potentially injuries. A well-balanced chainsaw, on the other hand, will distribute the weight evenly and reduce strain on the user's body. This is an important consideration when choosing a chainsaw, especially if you plan on using it for extended periods.

Finally, the weight of the chainsaw impacts its portability. If you need to transport the chainsaw to different locations, a lighter model will be easier to carry around. This is particularly important for professional users who need to move from job site to job site. A light weight chainsaw will allow them to work more efficiently and effectively.

In conclusion, the Einhell chainsaw is a popular and reliable tool that can handle a variety of tasks. Its weight is an important consideration for users, as it impacts its maneuverability, balance, and portability. If you're looking for a chainsaw that is easy to use, a lightweight model may be the best option. However, if you need a saw for heavy-duty tasks, a slightly heavier model may be more appropriate. Whatever your needs, be sure to choose a chainsaw that balances weight and functionality to help you get the job done right.

When it comes to buying a chainsaw, it's important to consider the tasks you'll be using it for. Einhell offers a variety of chainsaws, each with its own features that make it suitable for different applications. Here are some things to consider when choosing the right Einhell chainsaw for your needs:

1. Power and Bar Length: One of the most important factors to consider when buying a chainsaw is its power and bar length. If you plan to use your chainsaw for thick branches and large trees, then you'll need a chainsaw with a bigger engine and a longer bar. Einhell offers chainsaws with a bar length of 35cm to 45cm, and engine power ranging from 1.5 kW to 2.2 kW.

2. Safety Features: Safety should always be a top priority when using a chainsaw. Einhell chainsaws come with a range of safety features like chain brake, safety throttle, and anti-vibration system that reduce the risk of accidents while using the tool. It's important to choose a chainsaw with these features to ensure your safety while working.

3. User-Friendly Design: An ergonomic design can make it easier to handle and control the chainsaw. Einhell chainsaws come with features such as soft-grip handles, automatic lubrication, and tool-free chain tensioning that make it easier to use for extended periods of time.

4. Noise and Vibration: Noise and vibration levels can make a difference when it comes to choosing a chainsaw, especially if you plan to use it for prolonged periods. Einhell chainsaws come with features such as low noise and vibration levels, making them more comfortable to use, especially for prolonged periods.

5. Brand Reputation: Einhell is a reputable brand in the power tool industry, known for its quality products and reliable customer service. When buying a chainsaw, it's important to consider the brand reputation to ensure you're getting a quality product that will last long.

In conclusion, the right Einhell chainsaw for your needs will depend on the tasks you plan to use it for and the features that are most important to you. By considering factors like power, safety features, user-friendly design, noise and vibration levels, and brand reputation, you can find the right Einhell chainsaw for your needs.